Sample Form 1

GDT/On-Line Sample Procedures for Submission of
Engineering Drawing GD&T Callout Requirements
(ANSI Y14.5M-1982 & ASME Y14.5M-1994)

Tolerances of Location
* For Single Feature Control Frame Callout Up To 12 Feature Pattern Locations

* Note: Additional Feature Control Frame Callouts may be submitted by Fax or E-mail.

Sample Copy of GD&T Callout:

NOTES: Unless Otherwise Specified:
1. Interpret dimensions and tolerances per ASME Y14.5M-1994 Standard
2. Unspecified tolerances:
.X +/-.015 .XX +/-.010 .XXX +/-.005
3. Only the feature designated 2X Ų.144 +.005/-.001 is the subject of this analysis.

Sample Drawing (source unknown)

Tolerances of Location
For Single Feature Control Frame Callout Up To 12 Feature Pattern Locations*

* (Additional Feature Control Frame Callouts may be submitted by Fax or E-mail. )

1. Drawing Specifications of Dimensioning and Tolerancing Conform to:
ANSI Y14.5M-1982 ANSI Y14.5M-1994 Not Identified

2. Unit of Measurement: Inches Millimeters

3. (A) Specified Feature Form
and Size with Tol:
If specified dimension is BASIC (linear, circular, diametrical, radial or angular) enter dimension here:

     (B) Measured Feature Size (rounded to four decimal places)   1. 2.
     3. 4. 5. 6. 7. 8.
     9. 10. 11. 12. For additional holes, please fax or E-mail data in this SAME format. You MUST enter an appropriate reference I.D. # so that relevant data can be matched with this submission. Your I.D. #   E-mail info@techedusa.com

Feature Control Frame Callout

4. Geometric Characteristic Symbol: LOCATION

5. Specified Tolerance Form in Feature Control Frame:
Diametrical Non-Diametrical

6. Specified Tolerance Zone in Feature Control Frame:

7. Specified Material Condition (MC)*: MMC LMC RFS N/A

8. Specified Other Modifying symbols (as applicable):

9. Primary Datum Reference: Datum MC*
     Primary Datum Reference Form Is: O.D. I.D. Groove Surface
    Primary Datum Ref. Specified Size or N/A
     Measured Size or N/A

10. Secondary Datum Reference: Datum or N/A MC*
      Secondary Datum Reference Form Is: O.D. I.D. Groove Surface N/A
     Secondary Datum Ref. Specified Size or N/A
    Measured Size or N/A

11. Tertiary Datum Reference: Datum or N/A MC*
     Tertiary Datum Reference Form Is: O.D. I.D. Groove Surface N/A
     Tertiary Datum Ref. Specified Size or N/A
    Measured Size or N/A

Feature Location
(Single Feature Control Frame Specifications Only)

12. Location Pattern: Circular   Non-Circular
     You must specify B.C. Size for Circular or N/A for Non-Circular!
       B.C. Size for Circular or N/A Measured B.C. Size or N/A

Please enter the required values as given in # 3B above for as many measured features as were identified and in the same order.

13. Specified and Measured location in X-and Y- Axis:
Just as in Question 3 above, for additional holes please fax or E-mail data in this SAME format. You MUST enter an appropriate reference I.D. # so that relevant data can be matched with this submission. Your I.D. # E-mail info@techedusa.com

	Specified X-Axis	Measured X-Axis	Specified Y-Axis	Measured Y-Axis
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.

14. Please Assign A Reference I.D. For Our Response (optional): Note: If additional data is being submitted by Fax or E-mail, this reference I.D. must be assigned and must match the Reference I.D. assigned for this purpose above.

15. Contact Person:

16. Company Name:

17. Company Address: 1000 Your Street P.O. Box 0000

18. City: State or Province:

19. Country: Zip Code:

20. Phone Number and Extension:

21. Fax Number:

22. Your E-mail Address Where Results Should Be Sent:

23. Any additional information or comments, if applicable (optional):
Use this space for any additional information or comments you would like to add. For additional help in completing this form E-mail us at info@techedusa.com

*Important Note: Where feature/hole patterns are located by composite positional tolerancing or where tolerance requirements are specified in two single-segment feature control frames, please fax the GDT callout (only that portion of the drawing where the callout is shown). Email info@techedusa.com for details.

NOTE: This form has been completed as an example to be followed when submitting your own data. After completion of the form you would click the "Submit" button to send us your data for analysis. Once you have submitted your results, you will immediately receive confirmation that your submission has been received. We will analyze your data in the order it is received, and you will receive a full written disclosure of our findings.

Clicking the "Submit" button on this Sample Form will take you to an example of the written disclosure of our findings, which you can expect to receive based on the data you submit. Clicking the "Reset" button on this Sample Form will take you to an actual form where you may begin submitting your data.

If while entering your data you need to refer back to this Sample Form, simply use the BACK button on your browser. You may also feel free to print this Sample Form as a guide. If you have difficulty printing material displayed in frames, simply "drag" across some text within this frame before clicking the print button. If you need additional help, please contact us by E-mailing info@techedusa.com.

Click the Submit button above to see an example of our response. Click the Reset button above to begin submitting your own data.