GDT Form 1

Directions: Complete all information as indicated on the Sample Form.
To review the Sample Form, simply click here . . .

Engineering Drawing GDT Callout Requirements
(ANSI Y14.5M-1982 & ASME Y14.5M-1994)

Please Note: Enter ALL requested information. Select your options carefully. In order to validate this submission, you must answer all questions. You may enter Not Applicable (N/A) where appropriate. Space has been provided at the end of this form for any comments you feel may be pertinent to your submission. If any additional instructions are needed, please E-mail info@techedusa.com

Tolerances of Location
For Single Feature Control Frame Callout Up To 12 Feature Pattern Locations*

* (Additional Feature Control Frame Callouts may be submitted by Fax or E-mail. Appropriate directions will be given as you complete this form.)

FORM 1

Drawing Specifications of Dimensioning and Tolerancing Conform To:

ANSI Y14.5M-1982 ANSI Y14.5M-1994 Not Identified
Unit of Measurement: Inches Millimeters
(A) Specified Feature Form
and Size with Tol:
If specified dimension is BASIC (linear, circular, diametrical, radial or angular) enter dimension here:

(B) Measured Feature Size (rounded to four decimal places) 1. 2.
3. 4. 5. 6. 7.
8. 9. 10. 11.12. For additional holes, please fax or E-mail data in this SAME format. You MUST enter an appropriate reference I.D. # so that relevant data can be matched with this submission. Your I.D. # E-mail: info@techedusa.com

Feature Control Frame Callout

Geometric Characteristic Symbol: LOCATION
Specified Tolerance Form in Feature Control Frame:
Diametrical Non-Diametrical
Specified Tolerance Zone in Feature Control Frame:
Specified Material Condition (MC)*: MMC LMC RFS N/A
Specified Other Modifying Symbols (as applicable):
Primary Datum Reference: Datum MC*

Primary Datum Reference Form Is: O.D. I.D. Groove Surface

Primary Datum Ref. Specified Size or N/A

Measured Size or N/A
Secondary Datum Reference: Datum or N/A MC*

Secondary Datum Reference Form Is: O.D. I.D. Groove Surface N/A

Secondary Datum Ref. Specified Size or N/A

Measured Size or N/A
Tertiary Datum Reference: Datum or N/A MC*

Tertiary Datum Reference Form Is: O.D. I.D. Groove Surface N/A

Tertiary Datum Ref. Specified Size or N/A

Measured Size or N/A

Feature Location
(Single Feature Control Frame Specifications Only)
Location Pattern: Circular Non-Circular

You must specify B.C. Size for Circular or N/A for Non-Circular!
B.C. Size for Circular or N/A Measured B.C. Size or N/A

Please enter the required values as given in # 3B above for as many measured features as were identified and in the same order.

Specified and Measured Location in X- and Y- Axis:
Just as in Question 3 above, for additional holes please fax or E-mail data in this SAME format. You MUST enter an appropriate reference I.D. # so that relevant data can be matched with this submission. Your I.D. # E-mail: info@techedusa.com

	Specified X-Axis	Measured X-Axis	Specified Y-Axis	Measured Y-Axis
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.

Please Assign A Reference I.D. For Our Response (optional): Note: If additional data is being submitted by Fax or E-mail, this Reference I.D. must be assigned and must match the Reference I.D. assigned for this purpose above.
Contact Person:
Company Name:
Company Address:
City: State or Province:
Country: Zip Code:
Phone Number and Extension
Fax Number
Your E-mail Address Where Results Should Be Sent:
Any additional information or comments, if applicable (optional):

*Important Note: Where feature/hole patterns are located by composite positional tolerancing or where tolerance requirements are specified in two single-segment feature control frames, please fax the GDT callout (only that portion of the drawing where the callout is shown).